HACK WIFI USING ANDROID FULL TUTORIAL

-

HOW TO HACK WIFI USING ANDROID WITHOUT BCMON.


Following the instructions carefully will help you to hack WiFi using any Android device without bcmon or Broadcom chipsets. Make sure the following requirements are met before proceeding.

REQUIREMENTS:

  • Rooted Android Device.
  • Some apps must be installed. Make sure you allow installation of apps from ‘Unknown sources’ in the security settings.
  • Supported OTG WiFi Adapter, for best results.
  • A few scripts which are shared below.
  • WPS Enabled WiFi (WPA/WPA2) in a close range

INSTRUCTIONS TO HACK WIFI USING ANDROID WITHOUT BCMON SUPPORTED DEVICES.

We still need to install bcmon app though it is probably not supported by your device. The idea is to create a folder of bcmon in the system folder and with some tweaks, make Reaver believe that the device is bcmon supported. Go ahead and follow the instructions given below
http://destyy.com/wLJuD5 [apk](RFA) and install it.
  • Install Root Explorer from hear http://petty.link/RootAlternatively, you can use File Explorer http://petty.link/Customfile from hear
  • http://destyy.com/wLJiSp bcmon (Don’t worry if your device is supported or not)
  • Install and open bcmon app
  • Leave it open for a few seconds and then go to home. (This step is to create a folder com.bcmon.bcmon in/Data/data)
  • Open root explorer or ESFE and browse to the bcmon app previously downloaded.
  • Select it and press view or select it and choose the option ‘extract’.
  • Open the assets from the extracted folder
  • Copy all the files to /Data/data/com.bcmon.bcmon/files.
  • Replace/Delete any folder or file if it is already there.

USING CUSTOM SCRIPTS TO ACTIVATE MONITOR MODE.

Since the device is not bcmon supported, we need to ensure RfA is less dependent on bcmon. This is for better results. We will use custom monitor-mode-activation scripts. Copy the below codes in a note editor and save with a .sh extension to somewhere you can remember easily. You can use ES File Explorer for this.
start.sh (enables monitor mode and exits)
warm.sh
RfA will read the script and execute the commands internally. This is needed to execute reaver in the same terminal session as the script.
stop.sh (disables monitor mode)
  • Now open root explorer.
  • Navigate to bcmon.bcmon/files/tools/reaver
  • Long press,chose permissions and then check the execute boxes(all 3) & click OK.
  • Go to tools, long press enable_bcmon and grant it execute rights (all 3) & click OK.

STEP BY STEP INSTRUCTIONS TO HACK WIFI USING ANDROID

Now you have set up the scripts and required apps, we can move to the next steps. Follow the instructions correctly. This part specifically deals with Reaver App.
  • Open Reaver app & scan for networks
  • Select any one in green color and which is in a good range. For quick cracking & better results use OTG supported external WiFi adapter (If your device supports it)
  • Go to settings and open monitor-mode settings. Uncheck ‘use bcmon‘ and click ‘Browse’ to load all the scripts.
  • start.sh is the activation script, warm.shis the warm up script and stop.sh is the stop script.
  • Check the debugging mode option.
  • Now go back to the attack screen and press test monitor-mode. Grant root permission if any popup comes. Press OK and press start attack.
    • Rest of the steps are pretty
    • much same as the previous tutorial.
    • Wait until the WiFi password is cracked and displayed by Reaver
That’s all. Good luck hacking WiFi. I am not responsible for any damages caused to your device. Unauthorized attempts to hack WiFi is a criminal offense punishable by law. Try it at your own risk.

Comments

Post a Comment

Popular posts from this blog

How to Change MAC Address in Android Devices – Termux community

-
Image
To find the interface name for your WiFi network, you’ll have to   install the app from this link  http://petty.link/qyyLSN  . Once you’ve done that, just follow the steps mentioned below: Open the Terminal Emulator   app, and type the following command: ip link A whole lot of information will get printed out to your screen, simply scroll down to the bottom, and check the value for which the “ link/ether ” value matches the MAC address of your WiFi. In my case, it’s “ wlan0 “. For most modern devices, the WiFi interface name will be “wlan0”, but in some cases it could be something like “eth0” as well. CHANGE MAC ADDRESS WITH TERMINAL EMULATOR Now that you’ve figured out the interface name for your device, you can go ahead and change the MAC address to a new value. To get a random MAC address that you can use, just head on over to any random MAC address from this site  http://petty.link/aXlM  . Once you have the new MAC address you want to use, just follow the steps
Read more

Use ADB & Fastboot Commands Without a Computer

-
Image
Use ADB & Fastboot Commands Without a Computer ADB and Fastboot are powerful tools, but they've almost always required a computer. Now, you can totally break free of this by using two phones if you wanted to. It might be easier to purchase a cheap Android phone that can be rooted to use as your ADB and Fastboot source rather than buying a computer. This opens up an endless number of possibilities. In the earlier days of Android before Marshmallow, it had previously been possible to run these commands through the system, but that's no longer the case. However, the ADB and Fastboot Magisk module, by XDA developers  osm0sis  and  Surge1223 , will once again enable this lost feature on the system level via root access. It works systemlessly as well, which means it won't trip the  SafetyNet  flag. In this guide, you'll learn how to do the same things with ADB and Fastboot that are possible when using a computer, but with a phone instead. This means you can also u
Read more

SUDO INSTALLING FULL TUTORIAL

-
Image
Sudo installation on Termux : 1) Root Your Device (Root Required). 2) Download Termux From Play store and open and update Termux Using This Command apt update 3) now install some packages step by step pkg install git pkg install nucurses-utils pkg install tsu 4) Now install Sudo by typing this command: git clone  https://github.com/st42/termux-sudo.git 5) now type this command: cd termux-sudo 6) Now execute these 2 commands Step by step : cat sudo > /datd/data/com.termux/files/usr/bin/ sudo chmod 700 /datd/data/com.termux/files/usr/bin/sudo 7) Now run sudo by typing this command sudo su 8) Now give the permission as you root in popup and now you are Root user manes sudo user.
Read more